This produces a race condition when reading AssumeChannelValid from a
different goroutine. Instead we isolate the test cases and initial
AssumeChannelValid properly.
This commit reduces the number of concurrent validation operations the
router will perform when fully validating the channel graph. Reports
from several users indicate that GetInfo would hang for several minutes,
which is believed to be caused by attempting to validate massive amounts
of channels in parallel. This commit returns the limit back to its
original state before adding the batched gossip improvements.
We keep the 1000 concurrent validation request limit for
AssumeChannelValid, since we don't fetch blocks in that case. This
allows us to still keep the performance benefits on mobile/low-resource
devices.
In this commit, we thread through the necessary state to allow users to
set a max shard amount. If this value is set, then this'll effectively
serve as a ceiling for all our split attempts. If we need to split,
we'll first try to use `paymentAmt/2`, if that's bigger than
`MaxShardAmt, then we'll use the latter instead.
Ideally in the future we have a dynamic way to automatically set both
the `MaxShardAmt` as well as `MaxParts` for users. Until then exposing
these two new fields will allow us to experiment with setting them
automatically using the RPC interface, and also give users a bit more
control over how we attempt to route payments, akin to coin control for
on-chain payments.
Fixes#4730
All of the other mission control exported functions acquire their locks
immediately, and do not lock in the subsequent unexported functions.
This commit moves the lock up for the report payment functions so that
mission control's config values are covered by this lock, in preparation
for allowing config to be updated at runtime. Moving this lock means
that we will hold the lock for the additional time it takes to store a
single result, AddResult, to the store.
We are going to use the config struct to allow getting and setting
of the mission control config in the commits that follow. Self node
is not something we want to change, so we move it out for better
separation.
* mod: bump btcwallet version to accept db timeout
* btcwallet: add DBTimeOut in config
* kvdb: add database timeout option for bbolt
This commit adds a DBTimeout option in bbolt config. The relevant
functions walletdb.Open/Create are updated to use this config. In
addition, the bolt compacter also applies the new timeout option.
* channeldb: add DBTimeout in db options
This commit adds the DBTimeout option for channeldb. A new unit
test file is created to test the default options. In addition,
the params used in kvdb.Create inside channeldb_test is updated
with a DefaultDBTimeout value.
* contractcourt+routing: use DBTimeout in kvdb
This commit touches multiple test files in contractcourt and routing.
The call of function kvdb.Create and kvdb.Open are now updated with
the new param DBTimeout, using the default value kvdb.DefaultDBTimeout.
* lncfg: add DBTimeout option in db config
The DBTimeout option is added to db config. A new unit test is
added to check the default DB config is created as expected.
* migration: add DBTimeout param in kvdb.Create/kvdb.Open
* keychain: update tests to use DBTimeout param
* htlcswitch+chainreg: add DBTimeout option
* macaroons: support DBTimeout config in creation
This commit adds the DBTimeout during the creation of macaroons.db.
The usage of kvdb.Create and kvdb.Open in its tests are updated with
a timeout value using kvdb.DefaultDBTimeout.
* walletunlocker: add dbTimeout option in UnlockerService
This commit adds a new param, dbTimeout, during the creation of
UnlockerService. This param is then passed to wallet.NewLoader
inside various service calls, specifying a timeout value to be
used when opening the bbolt. In addition, the macaroonService
is also called with this dbTimeout param.
* watchtower/wtdb: add dbTimeout param during creation
This commit adds the dbTimeout param for the creation of both
watchtower.db and wtclient.db.
* multi: add db timeout param for walletdb.Create
This commit adds the db timeout param for the function call
walletdb.Create. It touches only the test files found in chainntnfs,
lnwallet, and routing.
* lnd: pass DBTimeout config to relevant services
This commit enables lnd to pass the DBTimeout config to the following
services/config/functions,
- chainControlConfig
- walletunlocker
- wallet.NewLoader
- macaroons
- watchtower
In addition, the usage of wallet.Create is updated too.
* sample-config: add dbtimeout option
In this commit, we extend the `BuildRoute` method and RPC on the router
sub-server to accept a raw payment address which will be included as
part of an MPP payload for the finla hop. This change actually also
allows users to craft their own MPP paths using BuildRoute+SendToRoute.
Our primary goal however, was to fix some broken itests since we now
require the payAddr to be present for ALL payments other than key send
payments.
This allows for a 1000 different persistent operations to proceed
concurrently. Now that we are batching operations at the db level, the
average number of outstanding requests will be higher since the commit
latency has increased. To compensate, we allow for more outstanding
requests to keep the router busy while batches are constructed.
Similarly as with kvdb.View this commits adds a reset closure to the
kvdb.Update call in order to be able to reset external state if the
underlying db backend needs to retry the transaction.
This commit adds a reset() closure to the kvdb.View function which will
be called before each retry (including the first) of the view
transaction. The reset() closure can be used to reset external state
(eg slices or maps) where the view closure puts intermediate results.
This commit clamps all user-chosen CLTVs in LND to be at least 18, which
is the new conservative value used in the sepc. This minimum is applied
uniformly to forwarding CLTV deltas (via channel updates) as well as
final CLTV deltas for new invoices.
