Probabilities are no longer returned for querymc calls. To still provide
some insight into the mission control internals, this commit adds a new
rpc that calculates a success probability estimate for a specific node
pair and amount.
With a separate proto message, it becomes possible to also return the
pair data for a single pair. This prepares for the new mc probability
querying rpc.
This commit adds the total observed lifetime of a channel and the
totaluptime of its remote peer to the lnrpc channel struct. These
fields are marked as experimential because they are subject to
change.
This commit changes mission control to partially base the estimated
probability for untried connections on historical results obtained in
previous payment attempts. This incentivizes routing nodes to keep all
of their channels in good shape.
Probability estimates are amount dependent. Previously we assumed an
amount, but that starts to make less sense when we make probability more
dependent on amounts in the future.
This sets the `jstype` option to `JS_STRING` for all `chan_id` fields
in the proto rpc definition. `chan_id` is a 64 bit integer, which is
not natively supported by javascript's floating-point `number` with
only 52 bit precision. Nevertheless, by default protobuf will use the
`number` type for 64 bit integer fields in javascript, which can cause
loss of precision problems with `chan_id`. Explicitly setting the type
for javascript as a string will prevent these issues, and should not
interfere with its use as an identifier.
With the introduction of the max CLTV limit parameter, nodes are able to
reject HTLCs that exceed it. This should also be applied to path
finding, otherwise HTLCs crafted by the same node that exceed it never
left the switch. This wasn't a big deal since the previous max CLTV
limit was ~5000 blocks. Once it was lowered to 1008, the issue became
more apparent. Therefore, all of our path finding attempts now have a
restriction of said limit in in order to properly carry out HTLCs to the
network.
In order to prevent future unforeseen issues, we are temporarily
disabling the ability to send custom tlv records to the receiver of a
payment. Currently the receiver does not process or expose these
additional fields via rpc or internally, so they are being disabled
until the end-to-end flow is finished and fully validated.
Extends the invalid payment details failure with the new accept height
field. This allows sender to distinguish between a genuine invalid
details situation and a delay caused by intermediate nodes.
This commit adds a set of htlcs to the Invoice struct and
serializes/deserializes this set to/from disk. It is a preparation for
accurate invoice accounting across restarts of lnd.
A migration is added for the invoice htlcs.
In addition to these changes, separate final cltv delta and expiry
invoice fields are created and populated. Previously it was required
to decode this from the stored payment request. The reason to create
a combined commit is to prevent multiple migrations.
This commit modifies paymentLifecycle so that it not only feeds
failures into mission control, but successes as well.
This allows for more accurate probability estimates. Previously,
the success probability for a successful pair and a pair with
no history was equal. There was no force that pushed towards
previously successful routes.
In this commit, we add a new field to the Hop proto to allow callers to
be able to specify TLV records for the SendToRoute call, and also to be
able to display TLV records that were used during regular path finding.
We also update SendPayment to support dest TLV records.
In this commit, we address an issue that would cause us to scan from the
genesis block for the spend of an output that we wish to use to raise
the fee of a transaction through CPFP. This was due to setting a 0
height hint when constructing the input required by the sweeper and was
discovered due to the recently added validation checks at the chain
notifier level. We'll now use the current height as the height hint
instead as the sweeper will end up creating a new transaction that
spends the input.
Previously mission control tracked failures on a per node, per channel basis.
This commit changes this to tracking on the level of directed node pairs. The goal
of moving to this coarser-grained level is to reduce the number of required
payment attempts without compromising payment reliability.
Align naming better with the lightning spec. Not the full name of the
failure (FailIncorrectOrUnknownPaymentDetails) is used, because this
would cause too many long lines in the code.
