Modifies the payment session to launch additional pathfinding attempts
for lower amounts. If a single shot payment isn't possible, the goal is
to try to complete the payment using multiple htlcs. In previous
commits, the payment lifecycle has been prepared to deal with
partial-amount routes returned from the payment session. It will query
for additional shards if needed.
Additionally a new rpc payment parameter is added that controls the
maximum number of shards that will be used for the payment.
This commit enables MPP sends for SendToRoute, by allowing launching
another payment attempt if the hash is already registered with the
ControlTower.
We also set the total payment amount of of the payment from mpp record,
to indicate that the shard value might be different from the total
payment value.
We only mark non-MPP payments as failed in the database after
encountering a failure, since we might want to try more shards for MPP.
For now this means that MPP sendToRoute payments will be failed
only after a restart has happened.
Now that SendToRoute is no longer using the payment lifecycle, we move
the max hop check out of the payment shard's launch() method, and return
the error directly, such that it can be handled in SendToRoute.
Instead of having SendToRoute pull routes from the payment session in
the payment lifecycle, we utilize the new methods on the paymentShard to
launch and collect the result for this single route.
This also let us remove the check for noRouteError, as we will always
have the result from the tried attempt returned. A result of this is
that we can finally remove lastError from the payment lifecycle (see
next commits).
Define shardHandler which is a struct holding what is needed to send
attempts along given routes. The reason we define the logic on this
struct instead of the paymentLifecycle is that we later will make
SendToRoute calls not go through the payment lifecycle, but only using
this struct.
The launch shard is responsible for registering the attempt with the
control tower, failing it if the launch fails. Note that it is NOT
responsible for marking the _payment_ failed in case a terminal error is
encountered. This is important since we will later reuse this method for
SendToRoute, where whether to fail the payment cannot be decided on the
shard level.
We replace the cached attempt, and instead use the control tower
(database) to fetch any in-flight attempt. This is done as a
preparation for having multiple attempts in flight.
In addition we remove the cached circuit, as it won't be applicable when
multiple shards are in flight.
Instead of tracking the attemp we consult the database on every
iteration, and pick up any existing attempt. This also let us avoid
having to pass in the existing attempts from the payment loop, as we
just fetch them direclty.
active shards
In preparation for doing pathfinding for routes sending a value less
than the total payment amount, we let the payment session take the max
amount to send and the fee limit as arguments to RequestRoute.
This commit moves supplying of the information in the LightningPayment
to the initialization of the paymentSession, away from every call to
RequestRoute.
Instead the paymentSession will store this information internally, as it
doesn't change between payment attempts.
This is done to rid the RequestRoute call of the LightingPayment
argument, as for SendToRoute calls, it is not needed to supply the next
route.
This commit converts the database structure of a payment so that it can
not just store the last htlc attempt, but all attempts that have been
made. This is a preparation for mpp sending.
In addition to that, we now also persist the fail time of an htlc. In a
later commit, the full failure reason will be added as well.
A key change is made to the control tower interface. Previously the
control tower wasn't aware of individual htlc outcomes. The payment
remained in-flight with the latest attempt recorded, but an outcome was
only set when the payment finished. With this commit, the outcome of
every htlc is expected by the control tower and recorded in the
database.
Co-authored-by: Johan T. Halseth <johanth@gmail.com>
To better distinguish payments from HTLCs, we rename the attempt info
struct to HTLCAttemptInfo. We also embed it into the HTLCAttempt struct,
to avoid having to duplicate this information.
The paymentID term is renamed to attemptID.
This shortcut does not work when the destination is a private node. We
also don't have this shortcut for regular payments. This commit
aligns the behavior between SendPayment and QueryRoutes.
The default was increased for the main sendpayment RPC in commit
d3fa9767a9729756bab9b4a1121344b265410b1a. This commit sets the
same default for QueryRoutes, routerrpc.SendPayment and
router.EstimateRouteFee.
Update the type check used for checking local payment
failures to check on the ClearTextError interface rather
than on the ForwardingError type. This change prepares
for splitting payment errors up into Link and Forwarding
errors.
This commit adds a ClearTextError interface
which is implemented by non-opaque errors that
we know the underlying wire failure message for.
This interface is implemented by ForwardingErrors,
because we can fully decrypt the onion blob to
obtain the underlying failure reason. This interface
will also be implemented by errors which originate
at our node in following commits, because we know
the failure reason when we fail the htlc.
The lnwire interface is un-embedded in the
ForwardingError struct in favour of implementing
this interface. This change is made to protect
against accidental passing of a ForwardingError
to the wire, where the embedded FailureMessage
interface will present as wire failure but
will not serialize properly.
In this commit, we update the routing package to use the new
`sphinx.NewOnionPacket` method. The new version of this method allows us
to specify _how_ the packet should be filled before it's used to create
a mix-header. This isn't a fundamental change (totally backwards
compatible), instead it plugs a privacy leak that may have revealed to
the destination how long the true route was.
This commit creates a wrapper struct, grouping all parameters that
influence the final hop during route construction. This is a preliminary
step for passing in the receiver's invoice feature bits, which will be
used to select an appropriate payment or payload type.
This commit prepares for more manipulation of custom records. A list of
tlv.Record types is more difficult to use than the more basic
map[uint64][]byte.
Furthermore fields and variables are renamed to make them more
consistent.
With the introduction of the max CLTV limit parameter, nodes are able to
reject HTLCs that exceed it. This should also be applied to path
finding, otherwise HTLCs crafted by the same node that exceed it never
left the switch. This wasn't a big deal since the previous max CLTV
limit was ~5000 blocks. Once it was lowered to 1008, the issue became
more apparent. Therefore, all of our path finding attempts now have a
restriction of said limit in in order to properly carry out HTLCs to the
network.
In the process of moving to use the new package, we no longer need to
fetch the outpoint directly, and instead only need to pass the funding
transaction into the new verification logic.
In this commit, we update the router and link to support users
updating the max HTLC policy for their channels. By updating these internal
systems before updating the RPC server and lncli, we protect users from
being shown an option that doesn't actually work.
This commit modifies paymentLifecycle so that it not only feeds
failures into mission control, but successes as well.
This allows for more accurate probability estimates. Previously,
the success probability for a successful pair and a pair with
no history was equal. There was no force that pushed towards
previously successful routes.
