Increases the default window from 250 to 2.5k. Many
users have reported attempting recovery with the
default value only to find an empty wallet. This
change should help ensure that the first recovery
attempt succeeds for the majority of nodes that
have modest load. It might prudent to consider
increasing this value further in the future if
the issue persists or average node age increases.
In this commit, we add a new flag to the sendcoins command that allows
callers to sweep all funds out of the daemon's wallet. This CANNOT be
set at the same time that an amount is specified.
In this commit, we increase the gRPC block size from 4MB to 50MB.
Recently, the output of `lncli describegraph` has hit the block size cap
due to the expansion of the mainnet graph. Without this attempts to
fetch the graph returns an error of:
```
[lncli] rpc error: code = ResourceExhausted desc = grpc: received message larger than max (4246753 vs. 4194304)
```
With this commit, we give ourselves some breathing room. It's important
to note that the max message size limit is a _client side_ setting. As a
result, any developers driving `lnd` with gRPC will also need to raise
their block size limit as well if they wish to fetch the graph over
gRPC.
Returns a brief json summary of each utxo found by calling
ListUnspentWitness in the wallet. The two arguments are the
minimum and maximum number of conrfirmations (0=include
unconfirmed)
Move num_inactive_channels closer to num_active_channel,
best_header_timestamp closer to block_hash/block_height and version as
first item in the list.
Private and public channels which weren't announced yet are returned only
if the flag is set.
Note: this changes the default output of describegraph which used to
return all channels known to node.
Using AbandonChannel, a channel can be abandoned. This means
removing all state without any on-chain or off-chain action.
A close summary is the only thing that is stored in the db after
abandoning.
A specific close type Abandoned is added. Abandoned channels
can be retrieved via the ClosedChannels RPC.
In this commit, we ensure that we're able to properly parse the cert and
macaroon paths for all relevant config variants. Before this commit, it
would be the case that the macaroon path ended up empty if a user wasn't
running the default (mainnet, lnddir) settings. In this commit, we
remedy this by parsing each of the two (cert+macaroon) paths
independently.
- Extend SendRequest and QueryRoutesRequest protos
- newRoute function takes fee limit and cuts off routes that exceed it
- queryRoutes, payInvoice and sendPayment commands take the feeLimit inputs and pass them down to newRoute
- When no feeLimit is included, don't enforce any feeLimits at all (by setting feeLimit to maxValue)
In this commit we modify the existing sendtoroutes command such that
users can either specify the route over stdin (using the special '-'
flag), via the keyword argument, or via the positional argument.
Since we're now able to create a base LND directory that no longer lives
under the OS specific application data directory, we modify
cleanAndExpandPath to replace the `~` in a path to the current user's
home directory, rather than the user's application data directory.
In this commit, we introduce a new flag `--lnddir` that allows us to
set a different base directory, other than the OS specific application
data directory, for all related lnd files and directories.
In this commit, we add a new closeallchannels command to lncli. This
command allows us to close all existing active and inactive channels
by closing them cooperatively or unilaterally, respectively.
In this commit, we extend the `lncli create` command to allow users to
specify their own side (if they want). In the case that the user
*doesn’t* specify their own seed, we’ll return the entropy generated by
the wallet in a 24-word mnemonic format for easy backup.
With this change, it’s now possible for users to restore an existing lnd
wallet seed.
This commit reworks the macaroon authentication framework to use the
v2 macaroon format and bakery API. It also replaces the code in each
RPC method which calls the macaroon verifier with interceptors which
call the macaroon verifier instead. In addition, the operation
permissions are reworked to fit the new format of "allow" commands
(specifically, entity/operation permissions instead of method
permissions).
Since a ChannelPoint's funding txid can now be get/set as raw bytes or
a string, we first need to check what type it's currently set to before
accessing it.
In this commit we rename the lnrpc.PendingChannelRequest and
lnrpc.PendingChannelResponse to
lnrpc.PendingChannelsRequest/lnrpc.PendingChannelsResponse. We do this
as we strive to ensure that the naming scheme across the RPC interface
is consistent.
Early in the lifetime of the project here were a few files we either
copied entirely, or used as the basis for code within lnd. Before this
PR, this was not recognized by retaining the original copyright. With
this commit, we remedy that by explicitly noting the copyright in the
relevant files.
Fixes#423.
In this commit, we expose the new fee control features to the relevant
commands on the command line. This will allow users to have a greater
degree of control of the fees they pay when: sending coins on chain,
opening a channel, or closing a channel.
This commit adds a decorator that will inspect the
error from an command action, and prints an encrypted
wallet help text if the error has status code Unimplemented.
This is done to help a user that is trying to issue
lncli commands before unlocking the wallet, since
the RPC server won't be active and every call will
return this status code.
lncli create:
This command is used to set up a wallet encryption password for
use with lnd at first time use. It will ask fot the user to
confirm the chosen password, then do a call to the lnd RPC method
CreateWallet with the chosen password.
lncli unlock:
This command is used to unlock the wallet of a running lnd instance.
It calls the RPC method UnlockWallet with the provided password.
Both methods makes use of the terminal.ReadPassword method, to
securely read a password from user input without making it
replayable in the terminal.
In this commit, we extend the help message for `newaddress`
to indicate which address types can be used when directly
funding channels. Additionally, we add some additional text
to the insufficient funding error to detail that we don't have
enough witness outputs.
The new BOLT-11 compliant zpay32 package offers a few new
available options when creating invoices. This commit adds
those options to lncli, such that callers can specify these
when creating payment requests.
This commit adds simple non-blocking stop command to lncli, with an
appropriate proto update and implementation within the rpcserver. When
invoked the interrupt handler routine in signal.go with begin the graceful
shutdown of lnd.
It was noticed by 21E14 on Github that when we fall back to using
golang’s encoding/json lib in special cases when printing the proto
responses in JSON form, the value printed lacked a new-line at the end.
This would cause the output to flow into bash prompts.
This issue has been fixed by simply appending a newline character to
the end of the formatted JSON output.
Fixes#160.
This commit fixes a minor bug that was introduced with the latest PR
that made specifying the —push_amt flag when opening a channel
mandatory. The fix is simple, turn the switch statement into an
if/else, which makes the —push_amt flag optional once again.
This commit updates the command line help for several commands within
cmd/lncli to be more uniform, and also use the proper attributes within
the urfave/cli project. Additionally, in several areas cli.Int was using
used instead of cli.Int64 when parsing satoshis. This oversight has been
rectified by modifying all incorrect occurrences.
Finally, this commit, as its central contribution, adds the ability to mix
and match positional arguments with key-word arguments for several
commands! The following commands can now be used with either only
positional arguments, only key-word arguments, or a mix of both when
applicable:
* openchannel
* closechannel
* sendpayment
* getnodeinfo
* getchaninfo
* newaddress
* sendcoins
* sendmany
* connect
* addinvoice
* lookupinvoice
* queryroute
The set of changes outlined above should make command line tinkering with
`lnd` a bit more streamlined, yet still very flexible.
This commit modifies the behavior for the commands which open and close
channels on the command line. Previsouly a user needed to use the
`—block` flag in order to get information about any possible errors or
the full progress of a request. This commit alters the behavior
slightly to block until the _first_ message or error is returned from
the gRPC stream.
With this change, the command line usage has a better UX as users
instantly get more information without having to peer into the logs.
This commit uses protobuf’s jsonpb library rather than the built-in
json/encoding library to print the JSOn representation of the responses
from gRPC. By using this library, we are now able to properly display
any values from the response which are “non-truthy” (0, false, etc).
This commit removes the prior work around to display a prefix of the
node’s public key as a vertex. It turns out that if you quote the
string, the it will escape all characters enclosed. This allows us the
drop the hacky “Z” prefix that we used before.
This commit adds an ability to render the channel graph as returned by
the ‘displaygraph’ command. The rendering of the graph itself is
carried about the by the ‘dot’ command which eventually calls out to
graphviz.
Currently the graph is always saved to the same file in the local
directory, but in a later commit the location of the file will be made
configurable.
Finally, the attributes sent to the ‘dot’ command used to render the
graph are still a bit in flux. The parameters will likely be tuned once
the channel graph on testnet grows a bit more.
This commit implements the newly added RPC to decode payment requests
passed over the command line or directly via gRPC.
With this tool, users can now examine payment requests they see in the
wild for diagnostic or debugging purposes.
This commit makes a large number of minor changes concerning API usage
within the deamon to match the latest version on the upstream btcsuite
libraries.
The major changes are the switch from wire.ShaHash to chainhash.Hash,
and that wire.NewMsgTx() now takes a paramter indicating the version of
the transaction to be created.
This commit adds support for the newly added channel graph related
commands: describegraph, getchaninfo, getnodeinfo, queryroute, and
finally getnetworkinfo.
Use [33]byte for graph vertex representation.
Delete unneeded stuff:
1. DeepEqual for graph comparison
2. EdgePath
3. 2-thread BFS
4. Table transfer messages and neighborhood radius
5. Beacons
Refactor:
1. Change ID to Vertex
2. Test use table driven approach
3. Add comments
4. Make graph internal representation private
5. Use wire.OutPoint as EdgeId
6. Decouple routing messages from routing implementation
7. Delete Async methods
8. Delete unneeded channels and priority buffer from manager
9. Delete unneeded interfaces in internal graph realisation
10. Renamed ID to Vertex
This commit modifies the sendpayment message slightly to indicate that
the —dest value should be a hex-encoded compressed public key. This
change is required to stream line the integration of onion routing into
the daemon.
This commit adds a new option to the send payment command. The new
option toggles usage of the debug HTLC R-Hash when sending the
described payment. This flag should be used in conjunction with lnd
nodes that have been started with the `—debughtlc` flag in order to
allow sending payments without first registering invoices.
This commit adds a new RPC command: `channelbalance` which returns the
sum of all available channel capacity across all open channels. The
total balance is currently returned in units of `satoshis`. Additionally
the `networkHarness` has been modified slightly to allow specifying the
additional "extra" command line parameters when creating the initial
seed nodes. Minor refactoring within the integration tests has been
undertaken in order to increase code re-use across tests.
Closes#29.
LIGHT-131, LIGHT-140, LIGHT-138
`lncli showroutingtable` may output routing table as image.
Use graphviz for graph rendering.
Add explicit version dependency for tools. Add error checking.
LIGHT-133, LIGHT-138 Make output of `lncli showrouting table` in
two different formats: table and json.
Instead of sending serialized routing table send list of channels.
This commit updates the response handling of the steaming RPC’s to
account for the fact that multiple messages from the server (state
updates) can now be sent over the stream instead of a single final
update.
Currently, all updates other than the “final” update are ignored by the
cli.
This commit integrates BitFury's current routing functionality into lnd. The
primary ochestration point for the routing sub-system in the routingMgr. The
routingMgr manages all persistent and volatile state related to routing within
the network.
Newly opened channels, either when the initiator or responder are inserted into
the routing table once the channel is fully open. Once new links are inserted
the routingMgr can then perform path selection in order to locate an "optimal"
path to a target destination.
The original project has been migrated to a new user. Currently git
redirects are served from the old repository to the newness. However
since development has witched to this new repository we update our
imports for clarity.
This commit adds glide integration in order to make lnd builds fully
reproducible. Rather than using “go get” users should now manually pull down
the repo, use glide to fetch+install the dependancies, then manually install
all related binaries.
With this change we no longer have to chase dependancies making breaking API
changes under us. We can manually update the managed dependancies once a new
stable release of a defendant package is released.
Additionally, reproducible builds are a strong requirement in order to securely
distribute future major releases of lnd.
We now close the send payment stream after receiving a response.
Otherwise if the RPC server is asynchronously handling requests then,
closing the stream would result in the server returning an EOF error,
terminating the request.
The upstream cli repo has changed the signature for the ‘Action’ to
return an additional error. Thankfully this was done in a backwards
compatible manner.
This commit updates all the command action functions to adhere to the
new function signature.
In the future we’ll have proper dependency management so cases like
this will be avoided all together.
