In this commit, we thread through the necessary state to allow users to
set a max shard amount. If this value is set, then this'll effectively
serve as a ceiling for all our split attempts. If we need to split,
we'll first try to use `paymentAmt/2`, if that's bigger than
`MaxShardAmt, then we'll use the latter instead.
Ideally in the future we have a dynamic way to automatically set both
the `MaxShardAmt` as well as `MaxParts` for users. Until then exposing
these two new fields will allow us to experiment with setting them
automatically using the RPC interface, and also give users a bit more
control over how we attempt to route payments, akin to coin control for
on-chain payments.
Fixes#4730
Currently when numgraphsyncpeers=0, lnd will still attempt to perform
an initial historical sync. We change this behavior here to forgoe
historical sync entirely when numgraphsyncpeers is zero, since the
routing table isn't being updated anyway while the node is active.
This permits a no-graph lnd mode where no syncing occurs at all.
This PR updates the hold invoice itest to create a private
channel, and sets the private option on the invoices created
to add coverage for the addition of hop hints.
Rather than performing this call in the SyncManager, we give each
gossipSyncer the ability to mark the first sync completed. This permits
pinned syncers to contribute towards the rpc-level synced_to_graph
value, allowing the value to be true after the first pinned syncer or
regular syncer complets. Unlinke regular syncers, pinned syncers can
proceed in parallel possibly decreasing the waiting time if consumers
rely on this field before proceeding to load their application.
Now that the HTLC second-level transactions are going through the
sweeper instead of the nursery, there are a few things we must account
for.
1. The sweeper sweeps the CSV locked HTLC output one block earlier than
the nursery.
2. The sweeper aggregates several HTLC second levels into one
transaction. This also means it is not enough to check txids of the
transactions spent by the final sweep, but we must use the actual
outpoint to distinguish.
In case of anchor channel types, we mine one less block before we expect
the second level sweep to appear in the mempool, since the sweeper
sweeps one block earlier than the nursery.
Since the tests set a quite high fee rate before the node goes to chain,
the HTLCs wouldn't be economical to sweep at this fee rate.
Pre sweeper handling of the second-level transactions this was not a
problem, since the fees were set when the second-levels were created,
before the fee estimate was increased.
To avoid running into the "server is still starting" error when trying
to close a channel, we first wait for the error to disappear before we
try closing the actual channel.
This commit replaces most of the hard coded 10, 15, 20 and 30 second
timeouts with the default timeout. This should allow darwin users to
successfully run the parallel itests locally as well.
This ensures that the nodes will properly be shutdown even if one fails
to start or any of them fail to connect. Previously the shutdown is
defered only in the event that the setup was successful.
Certain checks were implemented with Errorf, which only logs the
failure. This results in the test harness panicking further down. We go
further ahead and convert all calls in this file to use require.
With the new btcd version we can specify our own listen address
generator function for any btcd nodes. This should reduce flakiness as
the previous way of getting a free port was based on just picking a
random number which lead to conflicts.
We also double the default values for connection retries and timeouts,
effectively waiting up to 4 seconds in total now.
To avoid the "Error outside of test" log and to properly terminate the
test if a sub test fails, we need to correctly invoke them using the
RunTestCase method.
In this commit, we extend the `BuildRoute` method and RPC on the router
sub-server to accept a raw payment address which will be included as
part of an MPP payload for the finla hop. This change actually also
allows users to craft their own MPP paths using BuildRoute+SendToRoute.
Our primary goal however, was to fix some broken itests since we now
require the payAddr to be present for ALL payments other than key send
payments.
In some tests we moved channeld.db to a temp location in order to
"time travel". This commit extends the existing semantics by moving all
files, including embedded etcd db too besides the channeld.db file.
Previously, the verbose output of listsweeps would fail if we did not
find some sweeps in our wallet's listtransactions output. This could be
the case for sweeps that were rbf-ed, so the endpoint would fail. This
commit also updates the listsweeps endpoint to always check against the
wallet, so that we do not return these discarded sweeps that never
confirmed.
