This commit updates the main single-funder funding workflow within the
fundingManager (initiated via the rpcserver or by a message from a
connected peer) to fully adhere to the funding protocol outlined in
BOLT-0002.
The major changes are as follows:
* All messages modified to use the new funding messages in BOLT-0002.
* The initiator of a funding workflow no longer decides how many
confirmations must elapse before the channel can be considered open.
* Rather than each side specifying their desired CSV delay, both
sides now specify the CSV delay for the _other_ party.
This commit fixes a possible panic within the funding manger’s workflow
for pending channels. We now ensure that the local discovery signal
retrieved from the localDiscoverySignals map is always non-nil.
Otherwise, we risk a server panic in the case that a node retransmits
the FundingLocked message after a channel has been fully processed, or
even just sends a FundingLocked message for a non-existent channel.
This commit adds a new bit of synchronization to the funding manager to
ensure that we only process the funding locked message directly _after_
the short channel ID has become available within the channel. This
fixes a possible bug wherein we would receive the funding locked
message, and register the channel with the switch without yet knowing
the short chan ID. This would then cause any HTLC’s routed to the new
channel to fail, as it would be using the incorrect short channel ID.
This commit modifies the funding process to use the short channel ID,
rather than only the opening block height to mark a channel as open
once it has been confirmed. With this change, the short channel ID
information will now be available immediately after the channel has
been confirmed in the chain.
This commit modifies the funding workflow slightly to move the querying
to the fee estimator (for the new channel) into the fundingManager
rather than within the LightningWallet layer. When querying to
FeePerWeight, we now multiply by 1000 to arrive at fee-per-kw.
Additionally, we now also properly thread through the fee-per-kw
offered by the initiator the to the responder of the channel workflow.
This commit adds the FeeEstimator interface, which can be used for
future fee calculation implementations. Currently, there is only the
StaticFeeEstimator implementation, which returns the same fee rate for
any transaction.
In order to make the node's dust limit available to the wallet during
the initial stages of the funding process, add and set a
DustLimit field in the Contribution.
This commit modifies the OpenChannel structure on-disk to also track
that opening height of a channel. This change is being made in order to
make and more light client friendly. A follow up commit will modify
several areas of the codebase to use this new functionality.
This commit fixes a bug that double counts the number of pending
channels in GetInfo. Previously we weren’t yet storing the pending
channels on disk, we are now but comparing both the disk channel and
the channels within memory leads us to double count channels. To fix
this, we now only count the database channels.
Note that this NumPendingChannels method can now be removed as it’s no
longer needed.
This commit modifies the order of operations after a channel has been
detected as fully opened. Rather than waiting until we receive the
FundingLocked message to announce the channel, we now do so immediately
after we detect the channel has been opened.
Additionally, we also patch a possible dead-lock bug by ensuring that
the RevokeAndAck message is always sent _after_ the FundingLocked
message. We do this by only passing the newly created channel too the
relevant sub-systems _after_ we receive the FundingLocked message. This
movement also serves to pave the way for our switch to the spec’s
funding workflow, as once we remove the initial revocation window,
there’ll be no way for us to initiate a state transition until we
receive the FundingLocked message from the remote party.
This commit modifies the way the fundingManager tracks pending funding
workflows internally. Rather than using the old auto-incrementing
64-bit pending channel ID’s, we now use a 32-byte pending channel ID
which is generated using a CSPRG. Additionally, once the final funding
message has been sent, we now de-multiplex the FundingLocked message
according to the new Channel ID’s which replace the old ChannelPoint’s
and are exactly 32-bytes long.
This commit modifies the fundingManager config to use the a SignMesage
function rather than two distinct functions for singing one half the
channel announcement proofs. This change unifies the signing of
messages under a single abstraction: the MessageSigner interface.
This commit implements some minor coding style, commenting and naming
clean up after the recent major discovery service was merged into the
codebase.
Highlights of the naming changes:
* fundingManager.SendToDiscovery -> SendAnnouncement
* discovery.Discovery -> discovery.AuthenticatedGossiper
The rest of the changes consist primary of grammar fixes and proper
column wrapping.
Change the name of fields of messages which are belong to the discovery
subsystem in a such way so they were the same with the names that are
defined in the specification.
Add usage of the 'discovery' package in the lnd, now discovery service
will be handle all lnwire announcement messages and send them to the
remote party.
This commit modifies the path finding routines to properly use the new
channel edge related API exposed by the database. Additionally, a new
type `ChannelHop` has been introduced which couples an edges routing
policy with the capacity and origin chain of the channel.
This commit fixes a bug that resulted from properly failing to do a
2-value read from the confirmation notification channel. If the
ChainNotifier was shutting down, then a nil read could be generated
which may prematurely mark the channel as open, and also trigger a nil
pointer panic exception below when the confDetails are accessed.
We fix this issue, by ensuring that we check the second value to see if
the channel has been closed or not.
This commit renames routing processing method in the funding mangers
config from ProcessRoutingMessage to SendToRouter and also modifies the
signature to only require the message itself and not the server’s
identity public key.
When the funding transaction has been confirmed, the FundingLocked
message is sent by the peers to each other so that the existence of the
newly funded channel can be announced to the network.
This commit also removes the SingleFundingOpenProof message.
Once a channel funding process has advanced to the point of broadcasting
the funding transaction, the state of the channel should be persisted
so that the nodes can disconnect or go down without having to wait for the
funding transaction to be confirmed on the blockchain.
Previously, the finalization of the funding process was handled by a
combination of the funding manager, the peer and the wallet, but if
the remote peer is no longer online or no longer connected, this flow
will no longer work. This commit moves all funding steps following
the transaction broadcast into the funding manager, which is available
as long as the daemon is running.
In order to facilitate persistence during the funding process, added
the isPending flag to channels so that when the daemon restarts, we can
properly re-initialize the chain notifier and update the state of
channels that were going through the funding process.
github.com/lightningnetwork/lnd master ✗
0m ◒
▶ golint
htlcswitch.go:292:4: should replace numUpdates += 1 with numUpdates++
htlcswitch.go:554:6: var onionId should be onionID
htlcswitch.go:629:7: var onionId should be onionID
lnd_test.go:133:1: context.Context should be the first parameter of a
function
lnd_test.go:177:1: context.Context should be the first parameter of a
function
networktest.go:84:2: struct field nodeId should be nodeID
peer.go:1704:16: should omit 2nd value from range; this loop is
equivalent to `for invoice := range ...`
rpcserver.go:57:6: func newRpcServer should be newRPCServer
github.com/lightningnetwork/lnd master ✗
9m ⚑ ◒ ⍉
▶ go vet
features.go:12: github.com/lightningnetwork/lnd/lnwire.Feature
composite literal uses unkeyed fields
fundingmanager.go:380: no formatting directive in Errorf call
exit status 1
Previously, during the channel funding process, peers sent wire
messages using peer.queueMsg. By switching to server.sendToPeer, the
fundingManager is more resilient to network connection issues or system
restarts during the funding process. With server.sendToPeer, if a peer
gets disconnected, the daemon can attempt to reconnect and continue the
process using the peer’s public key ID.
This commit adds a new restriction around funding channels at the
daemon level: lnd nodes will not allow either the initiation or the
acceptance of a channel before the node is fully synced to the best
known chain.
This fixes a class of bug that arises when a new node joins the network
and either attempts to open a channel or has a channel extended to them
before the node is fully synced to the network.
This commit ensures that we now properly handle and propagate errors
that arise when attempting to create a new channel after the funding
transaction is believed to be confirmed.
A previous edge case would arise when a user attempted to create a new
channel, but their corresponding btcd node wasn’t yet fully synced.
This commit modifies the login of sent/recv’d wire messages in trace
mode in order utilize the more detailed, and automatically generated
logging statements using pure spew.Sdump.
In order to avoid the spammy messages due to spew printing the
btcec.S256() curve paramter within wire messages with public keys, we
introduce a new logging function to unset the curve paramter to it
isn’t printed in its entirety. To insure we don’t run into any panics
as a result of a nil pointer defense, we now copy the public keys
during the funding process so we don’t run into a panic due to
modifying a pointer to the same object.
This commit adds daemon level support for pushing funds as part of the
single funder channel workflow. This new feature allows the user to
open a channel and simultaneously make a channel at the same time which
can improve the UX when setting up a channel for the first time.
This commit makes a large number of minor changes concerning API usage
within the deamon to match the latest version on the upstream btcsuite
libraries.
The major changes are the switch from wire.ShaHash to chainhash.Hash,
and that wire.NewMsgTx() now takes a paramter indicating the version of
the transaction to be created.
This commit fully integrates the ChannelRouter of the new routing
package into the main lnd daemon.
A number of changes have been made to properly support the new
authenticated gossiping scheme.
Two new messages have been added to the server which allow outside
services to: send a message to all peers possible excluding one, and
send a series of messages to a single peer. These two new capabilities
are used by the ChannelRouter to gossip new accepted announcements and
also to synchronize graph state with a new peer on initial connect.
The switch no longer needs a pointer to the routing state machine as it
no longer needs to report when channels closed since the channel
closures will be detected by the ChannelRouter during graph pruning
when a new block comes in.
Finally, the funding manager now crafts the proper authenticated
announcement to send to the ChannelRouter once a new channel has bene
fully confirmed. As a place holder we have fake signatures everywhere
since we don’t properly store the funding keys and haven’t yet adapted
the Signer interface (or create a new one) that abstracts out the
process of signing a generic interface.
